This manual belongs to the product library described in "IBM 2210 Nways Multiprotocol Router Publications" and describes a group of protocols supported by the 2210. A specific 2210 might not support all of the features and functions described in these manuals. If a feature or function is device-specific, that restriction is indicated in the relevant manual.
This manual refers to the 2210 as either "the router" or "the device". The examples in the library represent the configuration of a 2210, but the actual output you see may vary. Use the examples as a guideline to what you might see while configuring your device.
Who Should Read This Manual: This manual is intended for persons who install and operate computer networks. Although experience with computer networking hardware and software is helpful, you do not need programming experience to use the protocol software.
To get additional information: Changes may be made to the documentation after the books are printed. If additional information is available or if changes are required after the books have been printed, the changes will be in a file (named README) on diskette 1 of the configuration program diskettes. You can view the file with an ASCII text editor.
IBM Nways Multiprotocol Routing Services is the software that supports the IBM 2210 (licensed program number 5801-ARR). This software has these components:
The base code is installed at the factory on the 2210.
The Configuration Program is not pre-loaded at the factory; it is shipped separately from the device as part of the software order.
You can also obtain the Configuration Program for IBM Nways Multiprotocol Routing Services from the IBM Networking Technical Support home page. See Configuration Program User's Guide for Nways Multiprotocol and Access Services Products, GC30-3830, for the server address and directories.
The following conventions are used in this manual to show command syntax and program responses:
reload
In this example, you can enter either the whole command (reload) or its abbreviation (rel).
command [keyword1 or keyword2]
Choose one of the keywords as a value for the parameter.
time host ...
In this example, you enter the IP address of the host in place of the periods, as explained in the description of the command.
Media (UTP/STP) [UTP]
In this example, the media defaults to UTP unless you specify STP.
The key combination Ctrl - indicates that you should press the Ctrl key and the hyphen simultaneously. In certain circumstances, this key combination changes the command line prompt.
File Name: filename.ext
Library reorganization: Beginning with Version 3.2, the following changes to the organization of the library took place:
Information updates and corrections: To keep you informed of engineering changes, clarifications, and fixes that were implemented after the books were printed, refer to the IBM 2210 home pages at:
http://www.networking.ibm.com/220/220prod.html
The following list shows the books that support the IBM 2210.
Operations and Network Management
This book explains how to:
These books describe how to access and use the Multiprotocol Routing Services command-line router user interface to configure and monitor the routing protocol software and features shipped with the router.
They include information about each of the protocols that the devices support.
This book contains a listing of the error codes that can occur, along with descriptions and recommended actions to correct the errors.
Configuration
This book discusses how to use the Configuration Program.
This book contains examples of how to configure protocols using IBM Nways Multiprotocol Routing Services.
Safety
This book provides translations of caution and danger notices applicable to the installation and maintenance of an IBM 2210.
The following list shows the books in the IBM 2210 Nways Multiprotocol Router library, arranged according to tasks.
Planning and Installation
These books are shipped with the 2210. They explain how to prepare for installation, install the 2210, perform an initial configuration, and verify that the installation is successful.
These books provide translations of danger notices and other safety information.
Diagnostics and Maintenance
This book is shipped with the 2210. It provides instructions for diagnosing problems with and repairing the 2210.
The following list applies to changes in the software that were made in Version 3.3. The changes consist of:
The technical changes and additions are indicated by a vertical line (|) to the left of the change.
At the command prompts, you can obtain help in the form of a listing of the commands available at that level. To do this, type ? (the help command), and then press Enter. Use ? to list the commands that are available from the current level. You can usually enter a ? after a specific command name to list its options.
The multiple-level nature of the software places you in secondary, tertiary, and even lower level environments as you configure or operate the 2210. To return to the next higher level, enter the exit command. To get to the secondary level, continue entering exit until you receive the secondary level prompt (either Config> or +).
For example, to exit the ASRT protocol configuration process:
ASRT config> exit Config>
If you need to get to the primary level (OPCON), enter the intercept character (Ctrl-P by default).